Mold remediation cost in Dothan, AL
About 3,641 normal-hours a year at or above a 60° F dew point in the 1991-2020 hourly normals, and 45.1% of Dothan's 71,957 housing units built before 1980. Moisture and housing age are separate variables here, and in this market they stack.
Found mold today?The first 24 hours
- Don't disturb it. Aggressive scrubbing, sanding, demolition or spraying can disturb mold and disperse material before you understand the scope. If you've started, stop and close the area off.
- Limit use of the HVAC if growth is near a return, air handler or ductwork. Running the system may spread particles to other areas, so consider limiting the affected system until the situation is evaluated.
- Photograph everything first. Timestamped photos of the growth, the surrounding materials and any staining help document the loss if it becomes an insurance claim.
- Find the water. Look above and behind the growth, not just at it — a leak, a failed seal, a crawl-space vent. Remediation before the source is fixed is a repeat visit.
- Don't rush. Mold that's been there for weeks isn't an emergency because you noticed today. The EPA's 24–48-hour window is for actively wet materials; if it's dry and stable, get more than one opinion.
Local data snapshot
- Climate station
- CAIRNS FLD FT RUCKER · USW00003850
- NOAA normals
- 1991–2020
- Housing dataset
- Census ACS 5-Year
- Metro units analyzed
- 71,957
- Median year built
- 1984
- Detached single-family
- 70.4%
- Labor series (BLS OEWS)
- SOC 47-2061 + 47-1011
- Cost model
- v1-2026-08
- Last reviewed
- Sep 2026
Dothan's mold season
Monthly mean dew point at CAIRNS FLD FT RUCKER, 1991-2020 normals. MoldCostGuide uses 60° F outdoor dew point as a benchmark for elevated atmospheric moisture when comparing climates — a comparison metric, not a biological threshold at which mold begins to grow.
Vertical scale 28–70° F. Bars in orange clear the threshold.
Bulk water: 53.9 inches of precipitation a year, wettest in August (NOAA 1991–2020 monthly normals) — the outside-water pathway that dew point can't measure, alongside the humidity season above.
- Humid hours
- 3,641 89th pct. of 729 metros
- Housing pre-1980
- 45.1% 38th pct.
- Moisture & housing
- 36/100 69th of 729
- Detached houses
- 70.4% of the metro's stock
- Multifamily
- 12.5% shared-wall stock
- Local labor
- $21.24 per hour, BLS metro figure
Humid hours and percentiles: NOAA/NCEI 1991–2020 climate normals, station USW00003850. Housing: US Census ACS 5-Year. Labor: BLS OEWS, May 2025. Costs: MoldCostGuide cost model v1-2026-08.
WHAT DRIVES COST HEREA long moisture season met by the local building stock
Start with the air. The 1991-2020 normals at Cairns Fld Ft Rucker work out to about 3,641 hours a year at or above a 60° F dew point — 41.6% of the year — and about 2,885 at or above 65° F, or 32.9%. July's mean dew point is 72.2° F, and for June, July, August and September the hourly normals sit at or above the 60° F line. Annual precipitation is 53.85 inches, wettest in August. Dothan sits at the 89th percentile for humid hours.
The housing side cuts differently. Of 71,957 units, 45.1% predate 1980 and 15.9% predate 1960, with a median year built of 1984. Detached houses make up 70.4%, mobile homes 15.9%, multifamily 12.5%. Construction methods and materials changed across those decades, but age by itself tells you nothing about how an individual house handles water — drainage, ventilation, flashing and maintenance decide that, and none of them show up in Census year-built data.
Construction labor averages $21.24 an hour here, and it is the principal market-specific input in our pricing model. Modeled midpoints run $594 for surface mold in a single room, $2,276 for a crawl space, $2,539 for HVAC and $8,023 for a whole-house scope, with the whole-house range reaching $24,068. Scope and reconstruction cost can climb where more materials are affected. Alabama does not license mold remediators or assessors; rebuild work may still trigger builder licensing and local permits.
What makes this an Dothan estimate?
We don't take a national mold-remediation average and add a city multiplier. The pricing model uses Dothan-area construction wages with standardized assumptions for crew time, equipment, containment, disposal and contractor overhead. Dothan climate normals and housing data provide local context and comparison around that modeled price.
Two questions: where is it, and how big is it?
They give a useful starting estimate — actual cost also turns on the affected materials, how far contamination has spread, access and containment. Priced at Dothan's labor rate.
COST BY SCOPEWhat each type of job runs in Dothan
| Scope | Modeled midpoint | Range | |
|---|---|---|---|
| Surface mold, single room | $594 | $386–$1,040 | |
| Attic | $1,507 | $829–$3,014 | |
| Crawl space | $2,276 | $1,252–$5,235 | |
| HVAC system | $2,539 | $1,523–$4,824 | |
| Basement | $2,808 | $1,544–$5,896 | |
| Whole house | $8,023 | $4,412–$24,068 |
These figures cover remediation only — containment, removal, cleaning, disposal and post-remediation verification. Our modeled figures exclude reconstruction. A contractor may quote it separately or include it in a broader proposal, so ask whether drywall, insulation, flooring, trim and paint are included.
ESTIMATEEstimate your Dothan job
The table above is per scope. Add the specifics of your situation for a tighter, Dothan-specific range.
COMPARISONHow Dothan compares
| Metro | Normal hrs ≥60° F | Pre-1980 | Labor cost | Crawl space |
|---|---|---|---|---|
| Dothan, AL | 3,641 | 45.1% | This metro | $2,276 |
| Panama City, FL | 4,401 | 25.2% | Well below | $2,702 |
| Crestview, FL | 4,047 | 23.3% | Below | $2,860 |
| Auburn, AL | 3,441 | 26.4% | Well below | $2,445 |
| Columbus, GA | 3,185 | 47.0% | Well below | $2,483 |
| Tallahassee, FL | 3,803 | 33.9% | Well below | $2,628 |
Panama City, 68 miles off, shows about 4,401 hours a year at or above 60° F against Dothan's 3,641, but only 25.2% of its stock predates 1980 — and its modeled crawl space midpoint is $2,702, against $2,276 here. Columbus, GA runs fewer humid hours, 3,185, with 47.0% pre-1980 and a "Well below" labor band. Climate and housing age move independently.
HOW IT STARTSMold growth depends on several conditions — and moisture is the one you can usually control
Mold spores are present in essentially every building — they arrive on clothing, on pets, and through every open door, and no remediation removes them permanently. The food source is the house itself: framing lumber, plywood, the paper facing on drywall, the dust on a joist. And the temperature range that supports growth covers most conditioned and unconditioned spaces for much of the year.
That leaves moisture — the condition a homeowner or contractor can actually influence, which is why every honest remediation conversation starts with where the water is coming from rather than what the growth looks like. Building scientists measure it as water activity: how much water is available at a material's surface, not the humidity of the air around it. Growth thresholds vary by species, material and how long a surface stays wet — some building-associated fungi can grow around 0.75 water activity (roughly 75% surface relative humidity), but the minimum varies considerably.
The ways water reaches a surface here
| Path | What it looks like | In Dothan |
|---|---|---|
| Seasonal humidity load | Outdoor air stays humid long enough that unconditioned spaces cannot dry between wetting events. | May-Sep |
| Crawl space ground moisture | Bare or poorly covered soil releases moisture upward into the floor assembly. | Year-round |
| Aging roof and flashing | Older penetrations and step flashing are the usual entry point for the leaks that start attic growth. | Storm-driven |
| Supply and drain plumbing | Concealed leaks wet cavity insulation and framing before anyone sees a stain. | Year-round |
RULES & OVERSIGHTMold regulation in Alabama
Alabama has no dedicated statewide mold-assessor or remediator licensing program Verified against state source
Alabama Department of Public Health states Alabama does not license mold remediation services.
Mold-regulation source: No dedicated state mold regulator; Alabama Department of Public Health provides environmental-health guidance — alabamapublichealth.gov · verified 2026-08-11
QUESTIONSWhat homeowners ask before they call
How much does mold remediation cost in Dothan?
Our modeled midpoint for surface mold in a single room is $594, with an estimated range of $386 to $1,040. Crawl space work models at $2,276 ($1,252 to $5,235), an attic at $1,507, HVAC at $2,539, a basement at $2,808, and a whole-house scope at $8,023 with a range of $4,412 to $24,068. Construction wages in the metro run about $21.24 an hour, one input on the labor side.
Is there a mold season in Dothan, or is it year-round?
There is a real warm season here. The 1991-2020 normals at Cairns Fld Ft Rucker put the July mean dew point at 72.2° F, and 5 months — May, June, July, August and September — clear a 60° F mean dew point. Across the year that works out to about 3,641 normal-hours at or above 60° F, 41.6% of the year, and 2,885 at or above 65° F. August is the wettest month within 53.85 inches of annual precipitation.
Can I clean this up myself or do I need a pro?
The EPA's guidance is that a homeowner may handle mold covering roughly 10 sq ft or less — think a patch on bathroom drywall you can see, reach and dry out. Beyond that, or where there's substantial water damage, HVAC involvement, contaminated water, or growth you suspect is hidden behind finishes or under the floor, professional guidance is more appropriate. For health questions, this page defers to the US EPA and the CDC.
Will my homeowners insurance pay for mold remediation?
It depends on the policy and the state. Coverage may apply when mold follows a sudden, accidental water loss — a burst supply line, a failed water heater. Policies may exclude or limit damage tied to long-term seepage, chronic humidity or deferred maintenance, which is the harder category in a market like this one. Read your declarations page and ask your insurer directly before work starts, and document the source with photos.
If I pay for remediation, will the mold come back?
Only the moisture answer makes it permanent. Removal without correcting the source — a wet crawl space, a leaking supply line, condensation on ductwork, grading that sends rain toward the slab — leaves conditions that raise the likelihood of recurrence. The EPA emphasizes moisture control as the core of the fix. Ask any remediator what they believe the water source is and how they verified it before the containment goes up.
How long does mold remediation take in a Dothan house?
It depends on the project. A contained single-room surface job is a short visit; crawl space, HVAC or whole-house scopes stretch longer because containment, removal, drying and rebuild are separate phases. Drying dominates the schedule — the EPA's guidance is to dry wet materials within 24-48 hours to limit further growth. Ask for a written sequence with a drying plan, not just a completion date.
What does mold remediation cost per square foot here?
Per-square-foot pricing is common shorthand and a poor predictor. Cost tracks affected area, access and containment far more than floor area — a tight Dothan crawl space with limited entry can take longer than an open room of the same footprint. Use the scope table instead: a single-room surface job models at $594, a crawl space at $2,276. Ask bidders to price the scope they can actually see.
Should I get a mold inspection before buying a house in Dothan?
Base the decision on evidence, not the listing year: visible growth, a musty odor, a history of roof or plumbing leaks, damp crawl space soil, or staining that keeps returning. It is worth noting that Alabama does not license mold assessors or remediators, so vet credentials yourself — ask whether the inspector follows the ANSI/IICRC S520 standard and whether they have any financial interest in the repair work they recommend.
Why we track dew point
Relative humidity shifts with temperature; dew point measures the actual amount of moisture in the air. We use it as a consistent way to compare the outdoor moisture load between markets, and high dew points also raise the chance of condensation when humid air meets cooler building surfaces. A single annual humidity average can't do that — it moves every time the temperature does, while dew point stays put.
Dew point is not a mold-growth threshold. Mold can grow without visible condensation wherever materials stay damp or surface humidity stays high — the US EPA recommends keeping indoor relative humidity under 60%. We track dew point because it is a stable, comparable signal of how much moisture the outdoor air actually carries, not because a given reading means mold begins.
WHAT'S GROWINGSpecies matters less than most people expect — and less than testing companies suggest
Most of what turns up indoors is one of a handful of genera — the CDC cites Cladosporium, Penicillium and Aspergillus as the most common. Appearance alone isn't a reliable way to identify the genus, and for a homeowner it rarely needs identifying. Some molds, including Stachybotrys chartarum, are associated with persistently wet, cellulose-rich materials — chronically damp drywall, or a crawl space with standing water.
| Question | Does species change the answer? |
|---|---|
| Removal method | Usually not. The approach is generally driven more by the extent of contamination, the affected materials and the moisture source than by the particular genus |
| Whether to remediate | No. Visible growth on a wet material gets removed whatever it is |
| Cost | Rarely. The driver is how wet and how widespread the growth is, not the name |
| Insurance claim | Sometimes. An insurer may ask for documentation of the loss and the damage; requirements vary by policy and carrier |
| Real estate transaction | It can. Independent documentation is useful when a sale needs a written record of conditions or completed work; requirements vary by transaction |
"Black mold" isn't a species
It's a colloquialism, usually meant to indicate Stachybotrys chartarum. Dark-colored growth is not enough to identify Stachybotrys or any other genus by sight. The remediation approach is driven more by the extent of contamination, the affected materials and the moisture source than by the color or common name of the mold. Be cautious about paying a premium simply because growth is described as “black mold” — identifying the type generally isn’t necessary before addressing the moisture and the growth.
On health effects, we defer to the sources that should own that question: the US EPA and the CDC. We're a cost and building-science resource, not a medical one.
THE DAMAGEWhat mold does to a house — and why cost climbs the longer it sits
Mold can grow on and within organic building materials when sufficient moisture is available. On the cellulose in drywall paper, framing lumber, insulation facing and subfloor, mold can degrade these organic materials over time, while prolonged wetting can independently soften, swell or rot the wood-based ones.
That's why cost tracks how far it has spread, not the size of the visible patch. Porous materials — drywall, insulation, carpet — can be difficult or impossible to clean once growth is established, and some may need to come out and be replaced. As more materials are affected, or as growth reaches concealed areas, the HVAC system or structural assemblies, the remediation scope and any reconstruction cost can climb. Staining and odor can also linger in materials after the surface looks clean.
The practical takeaway is why the first-24-hours steps matter: the longer wet materials stay wet, the more likely some will need removal rather than cleaning. On health effects, we defer to the US EPA and the CDC — this section is about the building, not a diagnosis.
BY PROJECT SIZEWhat affected area does to the number
Contractors quote in one of two ways: by the size of the affected area, or by the part of the house involved. Both appear below, because they answer different questions — size tells you the order of magnitude, scope tells you what the crew will actually be doing.
| Affected area | Crew & days | What our model assumes at this size |
|---|---|---|
| Under 10 sq ft | Often DIY | EPA says homeowners can handle many mold areas under about 10 sq ft themselves, depending on the material and circumstances |
| 10–50 sq ft | 2 crew · 1 day | Model assumes a single contained area, cleaning rather than removal; fixed costs dominate |
| 50–150 sq ft | 2 crew · 2–3 days | Model assumes containment and negative air, with porous materials starting to come out |
| 150–400 sq ft | 3 crew · 3–4 days | Model assumes significant demolition; rebuild becomes a separate trade and a separate bill |
| 400+ sq ft or multi-room | 4 crew · 5+ days | Model assumes a larger crew and multi-day work; containment, HVAC involvement and whether occupants can stay depend on site conditions |
Why per-square-foot estimates can mislead
Consumer cost guides often express mold-remediation pricing per square foot. It can be useful shorthand, but it is a poor predictor of an individual project, for two reasons. First, the figure applies to the affected area, not the room or the crawl space — a 1,200 sq ft crawl space with 80 sq ft of growth on the joists is an 80 sq ft job, and multiplying by the wrong number is an easy way to land on a figure several times too high. Second, small jobs are dominated by fixed costs: mobilization, containment setup and equipment delivery cost roughly the same whether the affected area is small or a bit larger, so the effective per-foot rate on a very small job runs much higher than on a mid-sized one.
WHAT A DETAILED QUOTE INCLUDESWhat to look for in a remediation proposal
ANSI/IICRC S520 is the principal industry procedural standard for professional mold remediation. A detailed proposal should describe the planned work clearly. Depending on the project, that may include:
| Line item | What it means |
|---|---|
| Assessment | Visual inspection plus moisture readings on suspect surfaces |
| Containment | Sealed barriers and, where the plan calls for it, negative air pressure so spores don't migrate during removal |
| Air filtration | HEPA-filtered air machines, used where containment is part of the plan |
| Material removal | Porous materials that can't be cleaned — drywall, insulation, carpet |
| Cleaning | HEPA vacuuming and appropriate cleaning of the surfaces that stay |
| Disposal | Contained and disposed of according to the remediation plan and applicable requirements |
| Verification | Post-remediation evaluation — a visual check and confirmation that materials are dry, with sampling where the situation calls for it |
WHAT IT'S LIKEWhat actually happens once work starts
| Question | What to expect |
|---|---|
| Does the inspection cost anything? | Some remediation companies offer a no-cost initial inspection or estimate. An independent assessment is a separate service and may carry a fee; it can be useful for larger, hidden or recurring problems, insurance matters or a home purchase, or when you want assessment kept separate from remediation |
| Do we have to move out? | It depends on the size and location of the work, the containment strategy and whether the HVAC system is involved. Ask the contractor whether the affected area can stay occupied during the work |
| What will the house look like? | Depending on the project, you may see containment barriers across doorways, HEPA-filtered air equipment running, and a section of wall, floor or insulation removed. It can look worse mid-job than before it started |
| Will it be put back? | Reconstruction may be performed by the remediation company, a related contractor or a separate trade, depending on the provider and proposal. Ask specifically what is included |
| How do I know it worked? | Post-remediation verification — a visual check that the area is clean and dry, with independent sampling where the situation calls for it |
How these numbers are built
Costs are modeled, not surveyed. We start from the wage of the trades that do the work in this metro, add loaded labor hours by scope, equipment days, containment materials and disposal, then apply a contractor margin. Every market is priced through the same model, so differences in the modeled figure reflect the local wage in the pricing formula rather than editorial judgment; climate and housing provide local context and comparison, not a cost input. Crew hours, equipment days and contractor margin are our own assumptions rather than published figures, and they are the least certain inputs in the model.
Model v1-2026-08. National output falls inside independently published cost ranges, which is a check rather than a source — we did not fit our figures to theirs.
Sources & references
- NOAA/NCEI, U.S. Climate Normals 1991–2020 — CAIRNS FLD FT RUCKER (USW00003850). ncei.noaa.gov/products/land-based-station/us-climate-normals
- U.S. Census Bureau, ACS 5-Year, tables B25034 / B25035 / B25077 — Dothan, AL Metro Area. data.census.gov/table?q=B25034
- U.S. Bureau of Labor Statistics, OEWS May 2025 — Construction Laborers (SOC 47-2061) and First-Line Supervisors of Construction (47-1011). bls.gov/oes/current/oes472061.htm
- US EPA, A Brief Guide to Mold, Moisture and Your Home — moisture control, ~10 sq ft DIY guidance, indoor RH under 60%. epa.gov/mold/brief-guide-mold-moisture-and-your-home
- US EPA, Mold Remediation in Schools and Commercial Buildings — 24–48 hour drying guidance. epa.gov/mold/mold-remediation-schools-and-commercial-buildings-guide
- CDC, About Mold — common indoor genera; testing generally not necessary. cdc.gov/mold-health/about/index.html
- ANSI/IICRC S520, Standard for Professional Mold Remediation.
- MoldCostGuide cost model v1-2026-08 — crew hours, equipment days, containment, disposal and contractor margin (our assumptions).
Cost model v1-2026-08 · generated 2026-09-23 18:59:45
Disclaimer: moldcostguide.com is a free service to assist homeowners in connecting with local service providers. All contractors/providers are independent and moldcostguide.com does not warrant or guarantee any work performed. It is the responsibility of the homeowner to verify that the hired contractor furnishes the necessary license and insurance required for the work being performed. All persons depicted in a photo or video are actors or models and not contractors listed on moldcostguide.com.